This is a legacy product

Technical support is available for this product. Availability of repair services should be verified with a technical support agent.

Replaced by:

QMOD-HDMI 1.5 HDTV Modulator-IPTV Encoder

Type: RF Modulators , IPTV Encoders
Part Number: 5093-001
Size: 8.500 wide x 1.730 high x 6.000 deep
Weight: 1.500
Distribution: AV over RF , AV over IP , Hybrid Systems
Released: May 2015

QMOD-HDMI 1.5 Product Manual
QMOD-HDMI 1.5 Data Sheet
CR Toolbox 4.4.4

  • QMOD-HDMI 1.5 Front View
  • QMOD-HDMI 1.5 Back View

More about RF Modulators

Modulation in its most basic definition is the mixing of two sinusoidal signals. The RF modulator takes an input signal and outputs a modulated signal to be transmitted as a video channel to any number of connected TVs. RF Modulators are used to distribute video in widely diverse installations, including stadiums, arenas, office buildings, college campuses, houses of worship, sports bars, and restaurants

About QMOD-HDMI 1.5 HDTV Modulator-IPTV Encoder

The QMOD-HDMI1.5 continues the QMOD track record for quality and innovation, setting a new benchmark for features and performance.

Full Description & Specifications

The dual-channel QMOD-HDMI 1.5, with one non-encrypted HDMI and one RGBHV/Component input, sets a new standard for sports, motion and digital signage encoding. Dual hardware scalers accept content up to 1080p, shapes VGA signage for edge-to-edge presentation, and compensates for non-broadcast and PAL refresh rates. Able to deliver two HD programs in one channel, the QMOD-HDMI 1.5 can also output the content as a Multicast or Unicast IPTV stream. Options include dual-language SAP audio, easy front-panel setup and alternate audio and NTSC video inputs. Web setup, monitoring, and firmware updates are available via USB and Ethernet ports. Two-across mounting offers up to four programs per rack space, with the ability to mix models to handle HDMI, SDI, Component, RGBHV and NTSC video sources.

Distribution: AV over RF , AV over IP , Hybrid Systems

  • MPEG-2 Profile:MP@HL for HD, MP@ML for SD
  • Auto-syncs to1080i, 720p, 480p, and 480i resolution, depending on input
  • Compensates for 60/30 Hz Component sources
  • Video Encoding bitrate 11, 13, 15, 18 or 25 Mbps (18 or less for dual-channel)
  • AC-3 (Pass-through or stereo) or MPEG-1, Layer 2 audio
  • MTS Dual-language capability
  • Optional scaling accepts VGA resolutions, over-scan compensation, and positioning
  • Optional dual-channel operation carries 2 full HD channels

  • Switchable 64/256 QAM, J83 Annex B, Interleaving Modes (128,1)
  • MER 38 dB typical

Front Panel:
  • Select and directional buttons for menu setup
  • Menu LCD, 2 lines of 20 white characters each

  • FCC Class B, ROHS, meets California standards

Back Panel:
  • Power: 2.1mm coaxial jack (inside center conductor positive)
    • 1.1A maximum, 11.5 to 13.5 VDC, 12 VDC typical
  • EAS: 3 Pin screw terminal; SW for latching closure, V+ (5-12 VDC), Ground
  • Ethernet: RJ-45 GigE Ethernet: Web page, control, streaming video
  • Video Inputs: HDMI (non-HDCP), up to 1080p
    • HD15 RGBHV/Component input up to 1080p, 59.94/60, 29.97/30 Hz
    • Composite Video: RCA female (480i), 29.97 Hz, also used for Line 21 captioning data
  • Audio Inputs: Two Digital SPDIF Coax RCA, PCM/AC-3 48K sample rate
    • Two 3.5mm stereo analog inputs
    • Inputs assignable to video inputs
  • RF: ‘F’, female, 75 ohm impedance
    • Agile, channels 2-135 (48-860 MHz), standard, HRC, or IRC spacing
    • 6 MHz bandwidth fits any open channel without interference to adjacent channels
    • 1 KHz resolution, +/- 30 ppm accuracy, +/- 35 ppm stability
    • 29 dB typical output power, attenuated in 5 steps, approx 4 dB
PS12-2.0 Product Image

PS12-2.0 Power Supply

12VDC 2A Power Supply